Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.NET

X  



TERMINATION Datasheet, PDF

Searched Keyword : 'TERMINATION' - Total: 9 (1/1) Pages
ManufacturerPart #DatasheetDescription
Company Logo Img
Diodes Incorporated
AP2303 Datasheet pdf image
947Kb/15P
DDR BUS TERMINATION REGULATOR
PI6CBF18501 Datasheet pdf image
1Mb/17P
Very Low Power 5-Output PCIe Fanout Buffer With On-chip Termination
October 2020
PI6CG15401 Datasheet pdf image
1Mb/18P
Ultra Low Power 4-Output PCIe Clock Generator With On-chip Termination
Rev 3 - 2 January 2022
PI6CG33802C Datasheet pdf image
1Mb/24P
3.3V Very Low Power 8-Output PCIe Clock Generator With On-Chip Termination
January 2020
PI6CG33201C Datasheet pdf image
1Mb/24P
3.3V Very Low Power 2-Output PCIe Clock Generator With On-chip Termination
Rev 3 - 2 January 2020
PI6CG33202C Datasheet pdf image
1Mb/24P
3.3V Very Low Power 2-Output PCIe Clock Generator With On-chip Termination
Rev 3 - 2 January 2020
PI6CG33401C Datasheet pdf image
1Mb/24P
3.3V Very-Low-Power 4-Output PCIe Clock Generator With On-Chip Termination
Rev 3 - 2 January 2020
PI6CG33402C Datasheet pdf image
1Mb/24P
3.3V Very-Low Power 4-Output PCIe Clock Generator With On-chip Termination
January 2020
PI6CG33801C Datasheet pdf image
1Mb/24P
3.3V Very Low Power 8-Output PCIe Clock Generator With On-chip Termination
Rev 3 - 2 January 2020

1


1



What is TERMINATION


Termination in electronic components means electrical termination.

It is commonly used to reduce signal-damaging reflections on the transmission line of electromagnetic waves.

For example, when sending a signal on a cable or printed circuit board (PCB), the signal travels to the end of the cable or PCB.

At this point, when the signal hits the end, some of the signal may be reflected and collide again.

These reflections can cause signal corruption and reduced speed.

Termination is therefore used to minimize these reflections and reduce signal noise from the ends.

Termination is usually implemented using resistors, capacitors or diodes.

A resistor of 50 ohms is usually used to close the ends.

This minimizes signal reflections and speeds up the transmitted signal.

*This information is for general informational purposes only, we will not be liable for any loss or damage caused by the above information.


Link URL :

Privacy Policy
ALLDATASHEET.NET
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com